FUEL SECTION RED PART NUMBERS INDICATE NEW PARTS 8-62 1 2 3 4 5 6 7 8 9 10 11 CONTENTS REFERENCE GENERAL EXHAUST FUEL DRIVE TRAIN ENGINE WHEEL CONTROL FRONT END FRAME ELECTRICAL Notes: • Stock motorcycles 1980 or earlier must be updated to a two cable pull open/pull closed throttle control system. A single cable pull open system cannot pull the throttle closed in case the throttle should accidentally stick in the open position. • S&S “Shorty” carburetors will not fit Harley-Davidson® Sportster® Ironhead models with vertical magnetos, due to clearance problems between the magneto and the carburetor. • Shovelhead engines with five gallon gas tanks and cylinders that are taller than stock require a special notched air cleaner cover to clear the gas tank. These taller engines also require a special length manifold. • S&S does not recommend polishing or chrome plating Super E & G carburetors. • Recommended for racing only - S&S Super E & G carburetors shown in this catalog section are not legal for use on motor vehicles operated on public highways in the state of California, or in other states where similar pollution laws may apply. The user shall determine the suitability of the product for his or her use and shall assume all risk and liability in connection therewith. Installation Installation is easy because carbs are sold in complete kits that contain everything needed to install the carb on the specified model motorcycle. All kits include manifolds for engines with stock length cylinders and a comprehensive, step by step installation booklet and tuning guide. Applications As a general rule, we recommend a Super E carb for engines up to about 100 cubic inches in displacement. The Super E’s smaller 1 7/8” (47.6mm) bore size creates higher air velocity, which results in better low and midrange response and power. Due to the Super G’s larger 2 1/16” (52.3mm) bore size, it is recommended for engines of no less than 90 cubic inch displacement. For the vast majority of engines in the 90-100 cubic displacement range, we strongly recommend the Super E because of the improved low and midrange response. However, if maximum peak horsepower is the most important consideration, a Super G carb would be appropriate. The S&S “Shorty” carbs are easy to tune due to the simple and functional design. The Super E & G’s are butterfly style carbs and have only two fuel circuits, not counting the starting system or accelerator pump. In addition, idle mixture, idle speed, and accelerator pump adjustments are easily accessible when the carburetor is installed on a motorcycle. The adjustable accelerator pump eliminates off idle hesitation and can be adjusted to provide the correct amount of fuel for a wide variety of engine displacements and styles. The accelerator pump is also very useful as a starting aid. To keep the carburetor bore unobstructed, the S&S “Shorty” carbs do not use a traditional choke plate for starting enrichment. Instead, a separate adjustable enrichment circuit is used for cold starts, which is also useful as an adjustable fast idle for cold engines. In addition to the larger bore size, another reason the “Shorty” carbs are capable of making more power is the design of the air cleaner. The most important factors are that the large surface area and the composition of the filter element present minimal restriction to the flow of air, and almost as important is the elimination of turbulence at the inlet of the carburetor. The filter area of the “Shorty” carbs is maximized by an ingenious backplate design that wraps slightly around the carb to allow room for a wider filter element than a straight backplate would allow. The pleated S&S filter element looks like paper, but is actually a special resin impregnated cellulose fiber media that provides excellent filtration as well as superior flow. The shape of the S&S air cleaner backplate and a directional cone inside the air cleaner cover also provides a smooth path for air to follow while traveling into the carburetor inlet. This results in less turbulence and greater air flow. *Outside oil lines that feed heads on Knucklehead and 1963/1965 Panhead engines must be refabricated or use a 1” spacer block for additional clearance. **Does not fit engines equipped with vertical magneto. S&S® SUPER E & G CARBURETOR KITS Big Twin Super E Kit Part # Super G Kit Part # 1955/1965 82002* –– 1966/1978 82003 –– 1979/1984 82004 –– 1984/1992 82005 82018 1993/1999 82006 82019 1999/2005 82007 82020 2006 82008 82021 Carb only, 82026 82027 all year groups Sportster Super E Kit Part # Super G Kit Part # 1957/1978 82009** –– 1979/1985 82012** –– 1986/1990 82013 –– 1991/2003 82014 –– 2004/2006 82015 –– Carb only, 82026 - Natural 82027 all year groups 82028 - Black Replacement Part Description Part # Replacement Cable Guide 82605 • Long version for use with CV Style Cables S&S Carburetor Kits 82028 Black 82026 Natural Complete Kit Not legal for sale or use in California Super E & G Kits
RkJQdWJsaXNoZXIy MzYzNTI=